Flagpole Installation
Flagpole Installation
Flagpole Installation
Everything below is taken from the instruction sheets that ship in the box with your pole. Pick your pole type. If you are not sure which you have, call us at 866-964-7147.
HD Telescoping Flagpole (20 ft and 25 ft)
Commercial aluminum flagpole, external halyard (rope)
Commercial aluminum flagpole, internal halyard (winch)
Hiring it out
Printable instruction sheets
HD Telescoping Flagpole, 20 ft and 25 ft
Ground sleeve installation. Plan on one afternoon for the concrete, then 24 hours before the pole goes in.
Materials
Telescoping flagpole
PVC ground sleeve (included with the pole)
3 to 5 bags of 60 lb concrete mix
Tape measure or yard stick
Contractor's level
Small rock or coarse gravel
Container for mixing concrete
Procedure
1. Read all instructions carefully.
2. Dig a hole approximately 6 times the diameter of the flagpole and 4 inches deeper than the length of the ground sleeve. A larger hole may be required in light soils.
3. Place a bed of gravel or crushed rock in the base of the hole.
4. Examine the sleeve and make sure the stop bolt extends through the sleeve. This bolt keeps the flagpole off the gravel base.
5. Place crushed rock or gravel in and around the sleeve to a height of 2 inches above the base of the sleeve. This helps drainage.
6. Mix the concrete following the manufacturer's instructions.
7. Pour the concrete around the sleeve to approximately 2 inches from ground level. Do not get concrete inside the sleeve. Alternate: pour to ground level and finish to create a mow strip.
8. Place the flagpole into the sleeve and level it. When the sleeve is level, carefully remove the flagpole without disturbing the sleeve.
9. Let the concrete harden for at least 24 hours. Place a warning or an object near the hole so nobody disturbs the sleeve.
10. After 24 hours, install the flagpole and place dirt or landscape material around the sleeve for a finished look.
Use the plastic cap that comes with the pole to cap the sleeve whenever the flagpole is removed, so nothing gets lodged inside.
Care
Do not use any lubricants on your flagpole. Clean only with soap and water.
Half mast
Fly the flag from the small ring and double ring, leaving the large ring at the top empty.
Pin lock (optional)
The polycarbonate locking device covers the release button and locks with a nut and bolt or a small padlock. The pole must be in the fully raised position. It keeps anyone from lowering the pole.
Commercial aluminum flagpole, external halyard
Foundation depth is on the spec sheet that ships with your pole. As a rule it runs about 10% of the exposed height: 20 ft pole, 3 ft; 25 ft and 35 ft poles, 3 ft 6 in; 40 ft pole, 4 ft. Concrete is 3000 PSI, supplied by you.
1. Dig the foundation hole four to six times the butt diameter of the flagpole.
2. Set the foundation tube so that the top of the tube is one to two inches above finish grade.
3. Plumb the foundation tube and brace it so it will not move during the pour.
4. Pour concrete and trowel it even with the top of the foundation tube. Keep the inside of the tube dry.
5. Lay the pole on sawhorses and unwrap it. For sectional poles, check both ends for burrs. File off any you find and wipe the areas clean. Lubricate the jamb sleeves with liquid soap. Align the numbers on each section and jamb together. Numbers must be identical for a proper fit.
6. Screw the truck into the top of the pole, using a wrench for a tight fit. If a cap-style truck is used, tighten the set screws well.
7. Screw the ball into the truck and tighten the ball set screw. Tighten by turning the stem of the ball with a wrench, not by turning the ball itself.
8. If a flash collar is provided, slide it on from the bottom of the pole to above cleat level and attach the cleat with one screw to hold the collar until the pole is up. Then remove the cleat, slide the collar down, and replace the cleat. Caulk between the collar and the pole with waterproof sealant (roofing cement or asphalt sealant).
9. Thread the rope through the sheave (pulley) of the truck and tie the ends together so the rope cannot drop out during erection.
10. Erect the pole into the foundation tube and center it. Turn it so the cleat holes face the direction you want.
11. Place wood wedges (supplied by you) between the pole and the foundation tube and plumb the pole.
12. Pack dry sand between the pole and the foundation tube. Leave a two inch void at the top and fill it with waterproof sealant to keep water out of the sand.
13. Loop the snaps on the rope, spaced for the flag size you are using.
Important: when erecting sectional flagpoles, never place your sling above the joint. The sling must be below the joint so the two sections cannot separate during hoisting.
Yardarm poles: locate the three pre-drilled holes approximately 1/3 down from the top of the pole. Attach the 6 in x 9 in plate at this point, then attach the U-bolts around the yardarm and through the plate. Secure the nuts and washers, including the four small acorn nuts on the ends of the U-bolts.
Commercial aluminum flagpole, internal halyard
Foundation and pole
1. Dig the foundation hole four to six times the butt diameter of the flagpole.
2. Set the foundation tube so that the top of the tube is two inches above grade.
3. Plumb the foundation tube and brace it so it will not move during the pour.
4. Pour concrete and trowel it even with the top of the foundation tube. Keep the inside of the tube dry.
5. Lay the pole on sawhorses and unwrap it. For sectional poles, check both ends for burrs, file off any you find and wipe clean. Liquid soap the jamb sleeves. Align the arrows or numbers on each section and jamb together. Numbers must be identical for a proper fit.
6. Assemble the winch and cable (below) before raising the pole.
7. Screw the ball into the truck and tighten the ball set screw by turning the stem with a wrench, not the ball itself. The ball is optional on internal halyard poles.
8. If a flash collar is provided, slide it on from the bottom of the pole to above winch level and tie it to the pole with line until the pole is up. Then remove the line, slide the collar down, and caulk between collar and pole with waterproof sealant.
9. Erect the pole into the foundation tube and center it. Turn it so the access door faces the direction you want.
10. Place wood wedges (supplied by you) between the pole and the foundation tube and plumb the pole.
11. Pack dry sand between the pole and the foundation tube. Leave a two inch void at the top and fill it with waterproof sealant.
Important: when erecting sectional flagpoles, never place your sling above the joint.
Caution: use extreme care when installing flagpoles near overhead power lines or buried cables.
Winch and cable assembly
1. The upper and lower cable assemblies are pre-assembled at the factory.
2. Locate the truck with the factory installed cable assemblies.
3. Locate the lower cable assembly. This is the cable exiting from the threaded portion of the truck.
4. Using an electrical fish tape, feed the lower cable assembly through the 1-1/2 inch threaded hole at the top of the flagpole and pull the lower cable through the entire length of the pole.
5. A winch hole with a slotted keyway is about 4 ft above grade from the bottom of the pole. Using extreme caution, reach into this hole, grasp the cable and pull about 4 ft of cable through. The edges of this hole may be sharp.
6. You should now have all but a few inches of the lower cable assembly inside the pole or at the lower end. If not, repeat steps 1 through 5.
7. Screw the truck assembly into the top of the flagpole securely.
8. Locate the winch assembly. Remove the cylinder lock keys taped to the side of the winch. Remove the hex drive countersunk stainless steel screw from the rear of the winch. Keep the keys and screw; you need them later.
9. To remove the lock from the winch, insert the key, turn counter-clockwise and pull until the cylinder comes out.
10. Locate the cable retaining hole and cable retaining set screw. With the painted surface of the winch in your left hand and the unpainted surface in your right, look into the window of the winch. A 1/8 inch hole on the right side of the winch drum is the cable retaining hole.
11. Insert the loose end of the cable protruding from the winch hole into the cable retaining hole. Do not expose any cable on the other side of the drum.
12. Insert the crank handle into the recess, push in and turn clockwise until the cable retaining set screw is exposed. Tighten the set screw securely with the correct size wrench.
13. Using the square keyway as a pathway for the 1/8 inch cable, insert the cartridge into the winch hole.
14. Locate the 1/2 inch hole directly opposite the winch hole. Align it with the hole in the cartridge, insert the screw and tighten securely.
15. Insert the crank into the crank socket. Push in and turn clockwise until the upper cable starts to move toward the top of the flagpole.
16. Attach the rubber coated counterweight temporarily to the open chain link at the loose end of the upper cable.
Lock
To unlock: insert the key, turn counter-clockwise, pull out the cylinder.
To lock: insert the cylinder into the recess, turn clockwise until snug, apply slight pulling pressure, then turn the key about 1/2 turn counter-clockwise to remove it.
Hiring it out
You do not need a flagpole specialist. Any local general contractor, fence company, or sign company installs flagpoles routinely. Hand them the spec sheet that ships with your pole and they will quote the job in a day. Commercial poles over 35 ft are usually set with a small crane or boom truck, which a sign company will have.
Printable instruction sheets
HD Telescoping Flagpole ground sleeve installation (PDF)
Commercial aluminum flagpole installation, external halyard (PDF)
Commercial aluminum flagpole installation, internal halyard (PDF)
Questions during install? Call 866-964-7147, Monday to Friday, 8:30 to 5 Mountain.
